Home / Parameters / 10000W

10000W laser cutting parameters

10000W laser cutting parameters RFL-10000(100u)

Source modelRFL-10000(100u)

OpticsCollimator 100 / Focus 200

Rows83

Materials5

Parameter table

Switch material to see every thickness row for this configuration.

Trial-shot parameter — small batch onlyRecommended for production

Note: parameters marked in red are trial-shot values. Actual results vary significantly with material, gas and machine condition — they suit small-batch production only and are not recommended for high-volume runs. A higher-power laser is advised for series production.

Carbon steel

1 – 40 mm

Thickness (mm)	Speed (m/min)	Power (W)	Gas	Pressure (bar)	Nozzle (mm)	Focus position (mm)	Stand-off (mm)
1	40-45	10000	N₂/Air	12	1.5S	0	1
2	30-35	10000	N₂/Air	12	2.0S	0	0.5
3	25-30	10000	N₂/Air	13	2.0S	0	0.5
4	18-20	10000	N₂/Air	13	2.5S	0	0.5
5	13-15	10000	N₂/Air	13	2.5S	0	0.5
6	10-12	10000	N₂/Air	13	2.5S	0	0.5
8	7-8	10000	N₂/Air	13	3.0S	-1	0.5
10	3.5-4.5	10000	N₂/Air	13	4.0S	-3	0.5
10	2-2.3	6000	O₂	0.6	1.2E	+6	0.8
12	1.8-2	7500	O₂	0.6	1.2E	+7	0.8
14	1.6-1.8	8500	O₂	0.6	1.4E	+7	0.8
16	1.4-1.6	9500	O₂	0.6	1.4E	+8	0.8
20	1.2-1.4	10000	O₂	0.6	1.6E	+8	0.8
22	1.0-1.2	10000	O₂	0.7	1.8E	+9	0.8
25	0.5-0.65	10000	O₂	0.7	1.8E	+10	0.8
30	0.3-0.35	10000	O₂	1.3	1.8E	+11	1.2
40	0.2	10000	O₂	1.5	1.8E	+11.5	1.2

Stainless steel

1 – 40 mm

Thickness (mm)	Speed (m/min)	Power (W)	Gas	Pressure (bar)	Nozzle (mm)	Focus position (mm)	Stand-off (mm)	Frequency (Hz)	Duty cycle (%)
1	45-50	10000	N₂	10	2.0S	0	1
2	35-40	10000	N₂	12	2.0S	0	0.5
3	25-30	10000	N₂	13	2.0S	0	0.5
4	18-20	10000	N₂	12	2.0S	0	0.5
5	12-15	10000	N₂	15	2.5S	0	0.5
6	8-9	10000	N₂	8	3.5B	0	0.5
8	5-6	10000	N₂	7	5.0B	0	0.5
10	3.5-4	10000	N₂	5	5.0B	-1	0.5
12	2.5-3	10000	N₂	6	6.0B	-4	0.5
14	2-2.5	10000	N₂	6	7.0B	-6	0.3
16	1.6-2	10000	N₂	6	7.0B	-8	0.3
18	1.2-1.5	10000	N₂	14	5.0B	-9	0.5
20	1-1.2	10000	N₂	6	7.0B	-11	0.3
25	0.5-0.6	10000	N₂	6	7.0B	-13	0.3
30	0.25	10000	N₂	10	7.0B	+7	0.3	300~800	60~80
40	0.15	10000	N₂	15	7.0B	+9	0.3	300~800	60~80
1	45-50	10000	Air	10	2.0S	0	1
2	30-35	10000	Air	10	2.5S	0	0.5
3	20-25	10000	Air	10	2.5S	0	0.5
4	18-20	10000	Air	10	3.5B	0	0.5
5	15-17	10000	Air	10	3.5B	0	0.5
6	8-10	10000	Air	10	3.5B	0	0.5
8	6-7	10000	Air	10	3.5B	0	0.5
10	5-6	10000	Air	10	3.5B	-1	0.5
12	4-4.5	10000	Air	10	5.0B	-4	0.5
14	2.5-3	10000	Air	10	5.0B	-6	0.5
16	1.8-2	10000	Air	10	5.0B	-8	0.5
18	1.2-1.5	10000	Air	10	5.0B	-9	0.5
20	1-1.2	10000	Air	10	5.0B	-11	0.3
25	0.5-0.6	10000	Air	10	5.0B	-13	0.3
30	0.25-0.4	10000	Air	10	5.0B	-14	0.3

Aluminum alloy

1 – 40 mm

Thickness (mm)	Speed (m/min)	Power (W)	Gas	Pressure (bar)	Nozzle (mm)	Focus position (mm)	Stand-off (mm)
1	45-50	10000	N₂	12	2.0S	0	0.8
2	25-30	10000	N₂	12	2.0S	-1	0.5
3	20-25	10000	N₂	12	2.0S	-1	0.5
4	18-20	10000	N₂	12	2.0S	-2	0.5
5	14-16	10000	N₂	14	2.5S	-3	0.5
6	8-9	10000	N₂	14	2.5S	-3	0.5
8	5-6	10000	N₂	14	2.5S	-4	0.5
10	4-4.5	10000	N₂	14	5.0B	-5	0.5
12	1.6-2	10000	N₂	16	5.0B	-5	0.5
14	1.2-1.5	10000	N₂	16	5.0B	-5	0.5
16	1-1.2	10000	N₂	16	5.0B	-5	0.5
18	0.8-1	10000	N₂	16	5.0B	-5	0.5
20	0.6-0.8	10000	N₂	16	7.0B	-5	0.3
25	0.5-0.6	10000	N₂	16	7.0B	-5	0.3
30	0.25-0.45	10000	N₂	18	7.0B	+7	0.3
40	0.15-0.2	10000	N₂	18	7.0B	+8	0.3

Brass

1 – 16 mm

Thickness (mm)	Speed (m/min)	Power (W)	Gas	Pressure (bar)	Nozzle (mm)	Focus position (mm)	Stand-off (mm)
1	35-40	10000	N₂	12	2.0S	0	1
2	22-27	10000	N₂	12	2.0S	-1	0.5
3	15-20	10000	N₂	12	2.0S	-1	0.5
4	12-15	10000	N₂	12	2.0S	-2	0.5
5	10-11	10000	N₂	14	2.5S	-3	0.5
6	6-7	10000	N₂	14	2.5S	-3	0.5
8	4-5	10000	N₂	14	2.5S	-4	0.5
10	3.5-4	10000	N₂	14	5.0B	-5	0.5
12	1.6-2	10000	N₂	14	5.0B	-5	0.5
14	0.8-1	10000	N₂	16	5.0B	-8	0.5
16	0.5-0.7	10000	N₂	16	5.0B	-11	0.3

Copper (O2)

1 – 10 mm

Thickness (mm)	Speed (m/min)	Power (W)	Gas	Pressure (bar)	Nozzle (mm)	Focus position (mm)	Stand-off (mm)
1	25-30	10000	O₂	14	2.0S	-0.5	1
2	16-20	10000	O₂	14	2.0S	-1	0.5
3	12-15	10000	O₂	14	2.0S	-2	0.5
4	8-10	10000	O₂	12	2.0S	-3	0.5
5	5-6	10000	O₂	12	2.5S	-4.5	0.5
6	3.5-4	10000	O₂	12	2.5S	-5	0.5
8	1.5-2	10000	O₂	12	3.0S	-6	0.5
10	0.5-0.7	10000	O₂	12	4.0S	-8	0.5

Frequently asked questions

Are the laser cutting parameters free to view?

Yes. Every parameter table can be read without an account and without payment — all of it, no tiers. What is paid is not content: it is me looking at your specific machine.

Which laser cutting machines are covered?

The library holds 21 machine configurations and 1,668 parameter rows, covering carbon steel, stainless steel, aluminum, brass and copper. Each configuration page states its optics setup.

Optics: 10000W

Collimator 100 / Focus 200

Keep exploring

All machine configurations Export and offline access