LaserParams6000W parámetros de corte láser
6000W parámetros de corte láser RFL-6000(100u)
Tabla de parámetros
Cambie de material para ver todos los espesores de esta configuración.
Nota: los parámetros marcados en rojo son valores de prueba. Los resultados reales varían notablemente según el material, el gas y el estado de la máquina — solo sirven para producción en pequeñas series y no se recomiendan para producción en serie. Para series se aconseja un láser de mayor potencia.
Acero al carbono
1 – 25 mm
| Espesor (mm) | Velocidad (m/min) | Potencia (W) | Gas | Presión (bar) | Boquilla (mm) | Posición de foco (mm) | Distancia (mm) |
|---|---|---|---|---|---|---|---|
| 1 | 35-45 | 6000 | N₂/Air | 12 | 1.5S | 0 | 1 |
| 2 | 20-25 | 6000 | N₂/Air | 12 | 2.0S | -1 | 0.5 |
| 3 | 12-14 | 6000 | N₂/Air | 14 | 2.0S | -1.5 | 0.5 |
| 4 | 8-10 | 6000 | N₂/Air | 14 | 2.0S | -2 | 0.5 |
| 5 | 6-7 | 6000 | N₂/Air | 16 | 3.0S | -2.5 | 0.5 |
| 6 | 5-6 | 6000 | N₂/Air | 16 | 3.5S | -3 | 0.5 |
| 3 | 3.5-4.2 | 2400 | O₂ | 0.6 | 1.2E | +3 | 0.8 |
| 4 | 3.3-3.8 | 2400 | O₂ | 0.6 | 1.2E | +3 | 0.8 |
| 5 | 3-3.6 | 3000 | O₂ | 0.6 | 1.2E | +3 | 0.8 |
| 6 | 2.7-3.2 | 3300 | O₂ | 0.6 | 1.2E | +3 | 0.8 |
| 8 | 2.2-2.5 | 4200 | O₂ | 0.6 | 1.2E | +3 | 0.8 |
| 10 | 2.0-2.3 | 5500 | O₂ | 0.6 | 1.2E | +4 | 0.8 |
| 12 | 0.9-1 | 2200 | O₂ | 0.6 | 3.0D | +2.5 | 0.8 |
| 12 | 1.9-2.1 | 6000 | O₂ | 0.6 | 1.2E | +5 | 0.8 |
| 14 | 0.8-0.9 | 2200 | O₂ | 0.6 | 3.5D | +2.5 | 0.8 |
| 14 | 1.4-1.7 | 6000 | O₂ | 0.6 | 1.4E | +5 | 1 |
| 16 | 0.8-0.9 | 2200 | O₂ | 0.6 | 4.0D | +2.5 | 0.8 |
| 16 | 1.2-1.4 | 6000 | O₂ | 0.6 | 1.4E | +6 | 1 |
| 18 | 0.65-0.75 | 2200 | O₂ | 0.6 | 4.0D | +2.5 | 0.8 |
| 18 | 0.8 | 6000 | O₂ | 0.6 | 1.6S | +12 | 0.3 |
| 20 | 0.5-0.6 | 2400 | O₂ | 0.6 | 4.0D | +3 | 0.8 |
| 20 | 0.6-0.7 | 6000 | O₂ | 0.6 | 1.6S | +13 | 0.3 |
| 22 | 0.45-0.5 | 2400 | O₂ | 0.6 | 4.0D | +3 | 0.8 |
| 22 | 0.5-0.6 | 6000 | O₂ | 0.6 | 1.6S | +13 | 0.3 |
| 25 | 0.5 | 2400 | O₂ | 0.5 | 5.0D | +3 | 1 |
| 25 | 0.4-0.5 | 6000 | O₂ | 0.6 | 1.8S | +14 | 0.3 |
Acero inoxidable
1 – 20 mm
| Espesor (mm) | Velocidad (m/min) | Potencia (W) | Gas | Presión (bar) | Boquilla (mm) | Posición de foco (mm) | Distancia (mm) |
|---|---|---|---|---|---|---|---|
| 1 | 40-50 | 6000 | N₂ | 10 | 1.5S | 0 | 0.8 |
| 2 | 25-30 | 6000 | N₂ | 12 | 2.0S | -1 | 0.5 |
| 3 | 15-18 | 6000 | N₂ | 12 | 2.5S | -1.5 | 0.5 |
| 4 | 10-12 | 6000 | N₂ | 14 | 2.5S | -2 | 0.5 |
| 5 | 7-8 | 6000 | N₂ | 14 | 3.0S | -2.5 | 0.5 |
| 6 | 6-7 | 6000 | N₂ | 15 | 3.0S | -3 | 0.5 |
| 8 | 3.5-3.8 | 6000 | N₂ | 15 | 3.0S | -4 | 0.5 |
| 10 | 1.6-2 | 6000 | N₂ | 15 | 3.5S | -6 | 0.5 |
| 12 | 1-1.2 | 6000 | N₂ | 16 | 3.5S | -7.5 | 0.5 |
| 14 | 0.8-1 | 6000 | N₂ | 16 | 4.0S | -9 | 0.5 |
| 16 | 0.5-0.6 | 6000 | N₂ | 18 | 4.0S | -10.5 | 0.5 |
| 18 | 0.4-0.5 | 6000 | N₂ | 20 | 5.0S | -11 | 0.3 |
| 20 | 0.2-0.35 | 6000 | N₂ | 20 | 5.0S | -12 | 0.3 |
Aleación de aluminio
1 – 16 mm
| Espesor (mm) | Velocidad (m/min) | Potencia (W) | Gas | Presión (bar) | Boquilla (mm) | Posición de foco (mm) | Distancia (mm) |
|---|---|---|---|---|---|---|---|
| 1 | 30-45 | 6000 | N₂ | 12 | 1.5S | 0 | 1 |
| 2 | 20-25 | 6000 | N₂ | 12 | 2.0S | -1 | 0.5 |
| 3 | 14-16 | 6000 | N₂ | 14 | 2.5S | -1.5 | 0.5 |
| 4 | 8-10 | 6000 | N₂ | 14 | 2.5S | -2 | 0.5 |
| 5 | 5-6 | 6000 | N₂ | 14 | 3.0S | -3 | 0.5 |
| 6 | 3.5-4 | 6000 | N₂ | 16 | 3.0S | -3 | 0.5 |
| 8 | 1.5-2 | 6000 | N₂ | 16 | 3.0S | -4 | 0.5 |
| 10 | 1-1.2 | 6000 | N₂ | 18 | 3.5S | -4.5 | 0.5 |
| 12 | 0.6-0.7 | 6000 | N₂ | 18 | 4.0S | -5 | 0.5 |
| 14 | 0.4-0.6 | 6000 | N₂ | 18 | 4.0S | -5 | 0.3 |
| 16 | 0.3-0.4 | 6000 | N₂ | 20 | 5.0S | -8 | 0.3 |
Latón
1 – 12 mm
| Espesor (mm) | Velocidad (m/min) | Potencia (W) | Gas | Presión (bar) | Boquilla (mm) | Posición de foco (mm) | Distancia (mm) |
|---|---|---|---|---|---|---|---|
| 1 | 30-40 | 6000 | N₂ | 12 | 1.5S | 0 | 1 |
| 2 | 18-20 | 6000 | N₂ | 12 | 2.0S | -1 | 0.5 |
| 3 | 12-14 | 6000 | N₂ | 14 | 2.5S | -1 | 0.5 |
| 4 | 8-9 | 6000 | N₂ | 14 | 3.0S | -1.5 | 0.5 |
| 5 | 5-5.5 | 6000 | N₂ | 14 | 3.0S | -2 | 0.5 |
| 6 | 3.2-3.8 | 6000 | N₂ | 16 | 3.0S | -2.5 | 0.5 |
| 8 | 1.5-1.8 | 6000 | N₂ | 16 | 3.5S | -3 | 0.5 |
| 10 | 0.8-1 | 6000 | N₂ | 16 | 3.5S | -3 | 0.5 |
| 12 | 0.6-0.7 | 6000 | N₂ | 18 | 4.0S | -4 | 0.3 |
Cobre
1 – 6 mm
| Espesor (mm) | Velocidad (m/min) | Potencia (W) | Gas | Presión (bar) | Boquilla (mm) | Posición de foco (mm) | Distancia (mm) |
|---|---|---|---|---|---|---|---|
| 1 | 25-30 | 6000 | O₂ | 14 | 2.0S | -0.5 | 1 |
| 2 | 15-18 | 6000 | O₂ | 14 | 2.0S | -1 | 0.5 |
| 3 | 8-10 | 6000 | O₂ | 12 | 2.0S | -2 | 0.5 |
| 4 | 5-6 | 6000 | O₂ | 12 | 2.0S | -2 | 0.5 |
| 5 | 3-4 | 6000 | O₂ | 10 | 2.5S | -3 | 0.5 |
| 6 | 1.5-2 | 6000 | O₂ | 10 | 2.5S | -3 | 0.5 |
Preguntas frecuentes
¿Los parámetros de corte son gratuitos?
Sí. Cada tabla puede consultarse sin cuenta y sin pago: entera, sin niveles. Lo que se paga no es el contenido, sino que yo mire su máquina concreta.
¿Qué máquinas están cubiertas?
La biblioteca contiene 21 configuraciones y 1,668 filas de parámetros para acero al carbono, inoxidable, aluminio, latón y cobre. Cada página indica su óptica.
Óptica: 6000W
Colimador 100 / Foco 200
Artículos relacionados
Laser cuts then stops: why a cut dies halfway through
A cut that starts clean and dies mid-way is a changing fault, not a missing one. Heat, gas sag, nozzle soot…
2026-10-22Laser not cutting through: the order I check things in
Not cutting through describes what you see, not what is wrong. Here is the order I work through on a real call, before…
2026-10-22Power dropping with no alarm: where the loss actually is
The source reports normal output, the cut gets weaker, and nothing faults. Most of the time the energy is being lost…